100% Satisfaction Guarantee
Machine Embroidery Downloads: Designs & Digitizing Services from EmbroideryDesigns.com                  CART  |   DOWNLOAD  |   CONTACT
                 WISHLIST  |  MY ACCOUNT  | 
PRODUCTSView Results
{{prd._source.displayName}} {{prd._source.displayName}}
by {{prd._source.vendorCode}}
{{prd._source.definitionName | productType}}
Not Yet Rated
Search Options
Would you like to search using your current filters below?
  • {{value}}
Yes   No

Free Standing Lace Charms: Halloween, Christmas, Patriotic

(Click to View All Images)

  • Lace Halloween, Christmas or Patriotic Charms designs
  • Ultra solvy - water soluble stabilizer
  • Thread & bobbin thread (same color)
  • Sharp 11 needle
  • Paper towels
  • Bowl and water
  • Ornament Hooks
  • 3/4" Fishhook earrings
  • 4mm jump rings
  • Needle nose pliers
  • Necklace clasps
  • Transparent necklace cord
  • Jewelry glue
  • Cord or thin piece of elastic
  • Needle nose pliers
  • Beads
  • Ruler
  • Scissors
  • Designs used in this project

    Step 1:
    (Click Image to Enlarge)
    Cut a piece of solvy that is a little larger than your hoop.

    Step 2:
    (Click Image to Enlarge)
    Hoop solvy making sure that it is hooped very tightly.

    Step 3:
    (Click Image to Enlarge)
    Place hoop onto your machine and embroider the lace design(s) of your choice.

    Step 4:
    (Click Image to Enlarge)
    Once the design is done embroidering remove from the machine and trim the excess solvy around the outside of the design.

    Step 5:
    (Click Image to Enlarge)
    Then add hot/warm water to your container. The water should be high enough in the bowl so that the entire lace heart will be submerged.

    Place your lace design inside the container. Let the design soak for about 10-15 minutes. This will remove the solvy from the water and place on paper towel to dry making sure that it is flat.

    Step 6:
    (Click Image to Enlarge)
    Gather your supplies to make the earring.

    Step 7:
    (Click Image to Enlarge)
    Use your pliers to slightly open one 4mm jump ring.

    Step 8:
    (Click Image to Enlarge)
    Place the design onto the ring.

    Step 9:
    (Click Image to Enlarge)
    Place the fishhook earring onto the ring also.

    Step 10:
    (Click Image to Enlarge)
    Here you have the completed earring.

    Step 11:
    (Click Image to Enlarge)
    What we did first was to measure an existing necklace and cut the plastic necklace about 2" longer.

    Step 12:
    (Click Image to Enlarge)
    Place the necklace clasp onto the necklace near one end and tie it off with a couple of knots.

    Step 13:
    (Click Image to Enlarge)
    Now you will want to plan how you want your necklace to look. We suggest laying out the beads and other items in order of how they will go on the necklace. Now add them to your necklace along with your lace embroidery design.

    Step 14:
    (Click Image to Enlarge)
    Now that you have the beads on your necklace attach the other side on the clasp and tie it on. Close the clasp. Now stretch out the necklace and tape the clasp down to your table and tape the embroidery design down, pulling the necklace tight.

    Step 15:
    (Click Image to Enlarge)
    With a ruler beside the necklace position the beads where you would like them. You can use the ruler to make sure that the beads are in the same position on both sides.

    Step 16:
    (Click Image to Enlarge)
    Use your jewelry glue to secure a bead on each side of the embroidery design to keep it in place. Then glue each bead to the necklace on each side. After you have completed this step let the glue dry according to the instructions on the package.

    You can purchase Halloween Trees at most craft stores or you can make your own.

    Share this project:     
    Meet The Author: Starbird Inc.
    Starbird Inc. has been digitizing custom embroidery designs for over 25 years. They have seen so many wonderful and creative designs over the years that Starbird decided to create some of their own embroidery stock designs. Starbird Inc. is having a great time creating new and imaginative ideas and would like you to be able to enjoy them also.

    Rate this Project: Awful Poor Average Good Excellent    Not Yet Rated
    | |
    McAfee Secure sites help keep you safe from identity theft, credit card fraud, spyware, spam, viruses and online scams    This site protected by Trustwave's Trusted Commerce program   Click to Verify - This site has chosen a VeriSign SSL Certificate to improve Web site security

    ©2005 - 2017 Embroidery Designs
    Site Designed By Liventus
    New Message Alert
    New Message(s)
    Your custom digitizing order(s) has 1 new message(s) waiting for you. Please read immediately and respond to expedite the processing of your order(s).
    Read Message Now